product manual

PRODUCT DESCRIPTION

The HLK-LD303-24G IoT millimeter wave radar module can be used to detect moving targets in a small range, and output distance and high and low level information, and is not affected by temperature, humidity, airflow, dust, noise, brightness, etc. Strong anti-interference ability, can penetrate acrylic, glass, plastic and other thin non-metal materials.

HLK-LD303-24G has industry-leading excellent performance, small size, higher accuracy, and low power consumption. It can provide customers with ideal and better performance object movement monitoring solutions.

*The interface is a 4-pin lock terminal with a pitch of 1.25mm

product features

letter of agreement

Communication configuration

TTL serial port, default baud rate 115200, data bit 8, stop bit 1, no check bit. Fixed query command (HEX): 55 5A 02 D3 84. The module defaults to the query mode, sending a fixed hexadecimal query command, and the module reports distance and other data after receiving it successfully.

Communication format

A. Uplink data (send by module)

    *the data shows

Length: the number of bytes except the frame header and check byte, 0x0A, fixed byte
-Address: 0xD3, fixed byte;
-Distance: The unit is cm, which occupies 2 bytes, with the high order first;
-Reserved: 1 byte, value 0x00, fixed byte;
-Status: target presence or absence; 1 byte, 0: no one 1: no one;
-Signal strength: unit: k, occupies 2 bytes, high order first;
-Inching: Value 0 or 1; 0-no inching, 1-with inching;
-Radar off: Whether the radar is off, the value is 0 or 1, 0-not off/1-off;
-Check: Sum check, all bytes except check word threshold are sum, and the lower 8 bits are taken, occupying 1 byte.

B. Downlink data (module receiving)

    *the data shows

Frame header: fixed 2 bytes, 0xBAAB
-Address: 0x00, fixed byte;
-Command number: the command number for setting the maximum detection distance, 0xE5, fixed byte;
-Command parameters: set the maximum detection distance, occupying 2 bytes, with the high order first;
-Check: No check, 0x00, fixed byte;
-End of frame: fixed 2 bytes, 0x55BB;
-Return after successful setting: 0D 0A 77 72 69 74 65 20 6F 6B 0D 0A
That is, the ASII code "Enter + write ok + enter"

Module dimensions

Precautions

* The module detects relative moving objects in the area, and outputs information such as the distance of the object, and completely stationary targets are not detected.
* The default query mode (protocol 6), if you need continuous automatic reporting, change the protocol to 7. (Use the host computer to modify or send the instruction directly BAAB00F600070055BB)
* If the module design shell, the best distance between the radar antenna surface and the shell surface is 6mm, and the thickness of the shell is about 2~3mm. The shell material can not use metal or metal-plated paint. It is recommended to use PC or plastic or steel Wait.

Relationship between angle and farthest distance

    *test introduction

-Test target: human body;
-Installation: horizontal installation and vertical installation respectively;
-Red broken line: The module is installed horizontally, with the module as the center of the circle, the vertical line of the antenna surface is 0°, and each angle and the angle correspond to the longest distance relationship that can be detected;
-Blue fold line: The module is installed vertically, with the module as the center of the circle, the vertical line of the antenna surface is 0°, and each angle and angle correspond to the fold line of the farthest distance that can be detected.

Module host computer demo

1. Connect the serial port of the module according to the terminal guide in the figure above (please ignore the PCB printing when using the terminal, because the terminal is drawn from the drawing board), and connect the other end to the computer USB port (I use the CP2104 serial port to USB small board here) ), select the currently used serial port number, the baud rate is 115200, and the rest are just as default.

2. Regarding the modification of the maximum detection distance and sensitivity related settings of the module, please refer to the range value of the instruction table for details. It is not recommended to modify other than the maximum and minimum detection distance. (How to open the configuration item, the upper left corner of the host computer "function item"-"developer configuration"-key, please contact customer service. * Emphasis-if the parameters are modified, the batch will be released later Please be sure to contact the salesperson to burn the firmware according to the modified parameters of the test)